Nos Sniper 07166NOS Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 16

Nos Sniper 07166NOS Скачать руководство пользователя страница 16

when system is activated. Inadequate fuel delivery

due to restricted fuel
filter.

Inspect fuel filter.

Clean or replace filter.

Crimped fuel line.

Inspect fuel line.

Replace crimped line.

High rpm misfire when
system is activated.

Weak fuel pump.

Install fuel pressure gauge. Run engine
under load at wide-open throttle, with
system activated.

Repair/replace fuel pump.

Excessive spark plug
gap.

Inspect spark plugs.

Set spark plug gap at
0.030” to 0.035”.

Surges under
acceleration when
system is activated.

Weak ignition/ignition
component failure.

Inspect components (plug wires, coils,
etc.)

Replace worn
components.

Inadequate supply of
nitrous.

Check bottle weight.

Replace with full bottle.

Nitrous Oxide Accessories

SNIPER systems are calibrated for optimum performance with a bottle pressure of 950 psi. The pressure will change with temperature.
Heater kits are thermostatically controlled to keep the bottle near 85° F to provide correct pressure.

Bottle Heater (P/N 14164SNIPER)

is available for 10 & 15 lb. bottles.

Bottle Heater, P/N 14169SNIPER,

is pressure-controlled to keep your bottle at 950 psi.

Insulating the bottle helps maintain pressure by keeping heat in the bottle when it’s cold, or heat out when it’s hot outside. The blankets
are made of a rugged, easily cleaned Nylon outer s

hell with insulation. It’s also an excellent “dress up” accessory and perfect for

“covering” battle-scarred bottles.

Bottle Blanket (P/N 14165SNIPER)

is a 7” diameter blanket for the 10 lb. bottle.

#10 Bottle Heater P/N 14169NOS

#10 Bottle Blanket P/N 14165NOS

The

Nitrous Pressure Gauges, P/N 15910SNIPER (-4AN lines) or P/N 15912SNIPER (-6AN lines)

[0-1500 PSIG] are designed to

provide accurate (± 2% of full scale) readings of fuel pressure in carbureted applications.

The

Fuel Pressure Gauges, P/N 15906SNIPER

[0-120 PSIG]

and P/N 15900SNIPER

[0-15 PSIG] are engineered to provide accurate

(± 2% of full scale) readings for high and low fuel pressure applications.

Nitrous & Fuel Pressure Gauges

Learn more about performance fuel system parts we have.

«
...
14
15
16

Содержание Sniper 07166NOS

















Отзывы:

Нет отзывов