Norwood Kwik-Till HSD2500 Скачать руководство пользователя страница 21

Страница: 21 / 154

2 - SAFETY INFORMATION

2-11

A safety chain will help control drawn equipment should it

accidentally separate from the drawbar.

Using the appropriate adapter parts, attach the chain to the

tractor drawbar support or other specified anchor location.

Provide only enough slack in the chain to permit turning.

See your Kwik-Till dealer if a replacement chain is needed.

Your Kwik-Till safety chain has a strength rating equal to or

greater than the gross weight of the towed machine.

Do Not

use the safety chain for towing.

Tow Loads Safely

Stopping distance increases with speed and weight of towed

loads, and on slopes. Towed loads with or without brakes that

are too heavy for the tractor or are towed too fast can cause

loss of control. Consider the total weight of the equipment

and its load.

Observe these recommended maximum road speeds, or local

speed limits which may be lower:
• If towed equipment does not have brakes, do not travel

more than 20 mph (32 km/h) and do not tow loads more

than 1.5 times the tractor weight.

• If towed equipment has brakes, do not travel more than 25

mph (40 km/h) and do not tow loads more than 4.5 times

the tractor weight.

Ensure the load does not exceed the recommended weight

ratio. Add ballast to recommended maximum for tractor,

lighten the load, or get a heavier towing unit. The tractor

must be heavy and powerful enough with adequate braking

power for the towed load. Use additional caution when towing

loads under adverse surface conditions, when turning, and

on inclines.

Keep Riders Off Machine

Keep riders off. Riders on the implement or tractor are subject

to injury such as being struck by foreign objects and being

thrown off of the machine.

Содержание Kwik-Till HSD2500



























































































































































Результаты поиска

Содержание Kwik-Till HSD2500

Отзывы:

Похожие инструкции для Kwik-Till HSD2500

Бренды по названию

Популярные бренды

Norwood Kwik-Till HSD2500, Руководство оператора

Результаты поиска

Содержание Kwik-Till HSD2500

Отзывы:

Похожие инструкции для Kwik-Till HSD2500

Бренды по названию

Популярные бренды