NorthStar 1200-02-01 Скачать руководство пользователя страница 9

Страница: 9 / 56

M3 GPS INSTALLATION MANUAL Revision D

PAGE 5

SECTION TWO

Installation instructions

General information

This section contains information for installing and wiring the Northstar
M3 GPS, antenna, and interfaces.

All installation procedures should follow acceptable practices, methods,
and techniques as described in Advisory Circulars (AC) 43.13-1A and
43.13-2A.

Special installation

requirements

•

Before inserting or removing the M3 from the mounting tray, turn off

power to the tray using the avionics master switch or circuit breaker,

even if the unit’s power switch is turned off. This will prevent inrush

current from arcing across the power connector.

•

Use only a GPS antenna specified within this manual.

Only the

Northstar AN120, AN135, and AN155 antennas are approved for use

with the M3. Consult the factory for special applications not covered

in these instructions.

•

The GPS antenna must be mounted on the top of the aircraft.

•

The GPS antenna should be located at least two feet away from any

other antennas and from the vertical stabilizer and canopy.

•

Forced air cooling must be supplied to the unit for all installations.

•

Electrical noise suppression of existing equipment may be required to

obtain satisfactory performance.

Unpacking and inspection

The shipping carton contains the following components and parts:

•

M3 GPS navigator (Part No. 1200-02-01 or 1200-03-01) and war-

ranty card

•

Mounting tray assembly

•

GPS Antenna (AN120, AN135, or AN155)

•

M3 GPS Approach Reference Manual

(GM601)

•

M3 GPS Approach Pilot’s Guide

(GM606)

•

M3 GPS Approach Installation Manual

(GM611)

•

Parts kit bag containing:

1 ea. air intake seal  (HM502)
1 ea. coax connector socket  (KC225)
1 ea. coax connector plug  (KC310)

Содержание 1200-02-01

























































Результаты поиска

Содержание 1200-02-01

Отзывы:

Похожие инструкции для 1200-02-01

Бренды по названию

Популярные бренды

NorthStar 1200-02-01, Руководство по установке

Результаты поиска

Содержание 1200-02-01

Отзывы:

Похожие инструкции для 1200-02-01

Бренды по названию

Популярные бренды