Northern N3NVR Series Скачать руководство пользователя

Страница: 90 / 218

Network Video Recorder
User Manual

UI System Setting

Issue: V4.6.X(2022-04-24)

Figure 7-20

Disk Detection

Operation Steps

Step 1

Choose the disk from the drop-down list.

Step 2

Tick

All

key Area

to detect the disk. It will take some several minutes.

Step 3

Click Scan to scan the disk.

Step 4

The result of disk will show in interface

The green block means good, the red block means bad, if the red blocks are too much or at key

section, please change the disk immediately.

Please turn off the video recording before the disk is detected, otherwise the recording of video

maybe lost.

----End

NOTE

Содержание N3NVR Series



























































































































































































































Результаты поиска

Содержание N3NVR Series

Отзывы:

Похожие инструкции для N3NVR Series

Бренды по названию

Популярные бренды

Northern N3NVR Series, Руководство пользователя

Результаты поиска

Содержание N3NVR Series

Отзывы:

Похожие инструкции для N3NVR Series

Бренды по названию

Популярные бренды