background image

Storage 

 

35 

3.

 

Using a wrench, disconnect the plumbing that connects to the heating 
coil inlet.  The water will flow out of the heating coil.  This will protect 
the coil from freeze damage. 

4.

 

Open both water inlet ball valves and remove the cap from the water 
filter.  This will drain the pump and water inlet plumbing. 

 

Long Term freeze protection:  

(For more than 30 days) 

 

RV antifreeze will save the components from freeze damage and keep them 
lubricated. 
1.

 

Drain water from the feed tank. 

2.

 

Disconnect both high pressure hoses from the high pressure water outlet 
fitting. 

3.

 

Fill feed tank with 5 gallons of RV antifreeze.   

4.

 

Run the engine (with burner off) until RV antifreeze comes out of both 
high pressure water outlet openings.   

Make sure excess antifreeze is disposed of safely.   

Prepare engine for 
long term storage  

 

(if storing more than 
30 days) 

First prepare the engine for long term storage if you will not be using 
the pressure washer again for more than 30 days.   

Fuel can become stale when stored over 30 days.  Stale fuel causes acid and 
gum deposits to form in the fuel system which can cause malfunction of the 
engine.

 

 

1.

 

Prepare fuel system for storage: 

 

o

 

Drain all gasoline

 from the tank and carburetor.  This is most easily 

accomplished by 

running the pressure washer with the high pressure 

hose

 until the engine stops from lack of fuel. 

OR 

o

 

Add fuel stabilizer

 to the gasoline (following manufacturer's 

instructions) 

Fuel stabilizer steps: 
a.

 

Ensure gas tank is full. 

b.

 

Add fuel stabilizer to fuel tank. 

c.

 

Run pressure washer with high pressure hose

 at least 5 

minutes after adding stabilizer to allow it to enter the fuel 
system. 

d.

 

Shut off engine 

 

2.

 

Lubricate cylinder and piston: 

 

a.

 

Disconnect spark plug wire and remove spark plug 

b.

 

Add one teaspoon oil through spark plug hole 

c.

 

Place rag over spark plug hole and turn starter (or pull the recoil) a 
few times to lubricate the combustion chamber. 

d.

 

Replace spark plug, but do not reconnect the spark plug wire. 

Содержание M157597AG

































































Отзывы: