manualshive.com logo in svg

North Atlantic SRS 5330A, Руководство по эксплуатации

Поделиться
Скачать
North Atlantic SRS 5330A Скачать руководство пользователя страница 19

 

North Atlantic Industries, Inc.

 

631.567.1100 / 631.567.1823 (fax)                       

6/12/2018 

5330A Operations Manual Rev A6 

110 Wilbur Place, Bohemia, NY 11716 

www.naii.com              

Cage Code: 0VGU1 

Page 19 of  24 

 

 
 

 
 
I

NSTALLATION AND 

M

AINTENANCE

 

 

UNPACKING AND INSPECTION 

This instrument has been thoroughly tested, inspected, and evaluated at the factory before shipment. Care has been 
taken in the design of the wrapping and packaging material to insure that no damage results from mishandling. 
 
Inspect the instrument externally. Check the front panel for signs of damage to the switches, knobs, terminal jacks 
and  display.  Check  the  power  switch  and  thumbwheel  for  smooth  operation.  Switch  buttons  should  be  secure. 
Check the condition of the connectors and fuse on the back panel.  Check covers for damage and loose screws. If 
the  instrument  passes  this  inspection,  install  it  and  place  it  in  operation.  If  damage  is  found,  please  contact  NAI 
customer service through the NAI web-site, 

www.naii.com

 or call (631)-567-1100. 

 

SHIPPING 

The  original  shipping  containers,  along  with  their  appropriate  blocking  and  isolating  material  are  the  preferred 
method of packing.  Any other suitably strong container may be used provided the product is wrapped in a sealed 
plastic  bag  and  surrounded  with  an  appropriate  amount  of  shock  absorbing  material  to  cushion  firmly,  preventing 
movement  inside  the  container.    Special  attention  should  be  paid  to  protection  of  the  front  panel  touch  screen 
display and terminal jacks. 

 

INSTALLATION 

Rack Mounting Instructions: 

The  Model  5330A  may  be  mounted  in  a  standard  19-inch  equipment  with  a  full  rack  mounting  adapter,  NAI  p/n 
783893.  It requires no special cooling equipment. Mount  the unit so that  air flows freely  around it, particularly  the 
rear panel  used to transmit the power supply  heat to the ambient  air.   Connect cables, turn  on  power switch and 
wait for unit to initialize. 

 

Bench Installation:  

For bench top use, the 5330A has Tilt stand and (4) rubber feet. Select an appropriate area that permits access to 
front  and  rear  panels  of  SRS.    Place  SRS  on  bench,  connect  cables,  turn  on  power  switch  and  wait  for  unit  to 
initialize 
 

MAINTENANCE 

Input AC Power Fuse(s): 

Fuses  are  contained  within  the  AC  Input  Connector.  Insure  AC  Power  cord  is  disconnected.  Replacement  of  the 
fuses  is  accomplished  by  removing  the  fuse  holder  located  within  the  AC  Input  Connector  (external,  rear  panel  of 
unit). Replace with fuses equivalent to factory installed specifications. Reference the Mechanical Outline.  

 

 

 
 
 
 

Содержание SRS 5330A

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды