North American Tool 7216 Скачать руководство пользователя страница 1

8807216        09/13

6/12 VOLT CHARGER with ENGINE START

CALIFORNIA PROPOSITION 65

WARNING: You can create dust
when you cut, sand, drill or grind
materials such as wood, paint,
metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause
cancer, birth defects, or other
reproductive harm. Wear
protective gear.

WARNING: This product or its
power cord may contain
chemicals, including lead, known
to the State of California to cause
cancer and birth defects or other
reproductive harm. Wash hands
after handling.

CAUTION:

FOR YOUR OWN SAFETY, READ
INSTRUCTION MANUAL
COMPLETELY AND CAREFULLY
BEFORE OPERATING THIS
CHARGER ENGINE STARTER.

GENERAL SAFETY WARNING

Please read and understand all
instructions. Failure to follow all
instructions listed below may result
in electric shock, fire, and/or serious
personal injury.

WARNING: When using tool,
basic safety precautions should
always be followed to reduce the
risk of personal injury and
damage to the equipment.

SPECIFICATIONS

• 100/200 Amp Emergency Starter

• 6/12 Volt

• Amp meter monitors

• Heavy duty, 79” charging cables

• 3 hour charge timer with hold

• 12V-2A trickle charge for small 12V
Batteries

• 12V-40A for quick charging

• 6V-40A for fast charging

• 6V-40A for starting

SAFETY INSTRUCTIONS

1. SAVE THESE INSTRUCTIONS -
This manual contains important
safety and operating instructions for
this battery charger.

2. Do not expose charger to rain or
snow.

3. Use of an attachment not
recommended or sold by the
manufacturer may result in a risk of
fire, electric shock, or injury.

4. To reduce risk of damage to the
electric plug and cord, pull by plug
rather than cord when
disconnecting charger.

5. An extension cord should not
be used unless absolutely
necessary. Use of improper
extension cord could result in a
risk of fire and electric shock. If an
extension cord must be used,
make sure:

a. That pins on plugs of extension
cord are the same number, size,
and shape as those of plug on the
charger;

b. That extension cord is properly
wired and in good electrical
condition; and

c. That wire size is large enough
for AC ampere rating of charger
as specified in Table 1.

6) Do not operate charger with
damaged cord or plug - replace
the cord or plug immediately.

7) Do not operate charger if it has
received a sharp blow, been
dropped, or otherwise damaged in
any way; take it to a qualified
serviceman.

8) Do not disassemble charger;
take it to a qualified serviceman
when service or repair is required.

Model: 7216

For Customer Service, please call 

1-800-348-5004

 or 

email 

[email protected]

Содержание 7216












Отзывы: