Nortel Passport 7400 Скачать руководство пользователя страница 222 | Manualshive

Страница: 222 / 438

Nortel Passport 7400 Скачать руководство пользователя страница 222

222 Chapter 37 Hardware procedures

241-7401-240 5.2S1

Installing a 16-slot Passport switch power supply

Install a 16-slot Passport switch power supply to provide minimum or
redundant power to the shelf.

Prerequisites

•

You will need a power supply with one of the following PECs:

— NTBP09 AC

— NTBO52 DC

Procedure steps

1

If necessary remove the power supply blank from the power supply bay.
Blanks are removed and installed using the same procedure as for power
supplies.

2

Set the power switch on the power supply faceplate to the standby
position. See the figure “Unlocked power supply with power switch in the
standby position” (page 355).

3

Use a 1/4-in. flat-head screwdriver to turn the locking screw on the power
supply faceplate to the unlocked (vertical) position.

4

Pull the faceplate handle down so that the handle is at a 90˚ angle to the
faceplate.

5

Use both hands to lift the power supply. Grasp the handle and lift with one
hand. Support the bottom of the power supply with the other hand. See

WARNING

Risk of personal injury

Power supplies weigh 6.6 kg (14.5 lb) each. Handle
carefully and avoid dropping.

WARNUNG

Verletzungsgefahr

Die Stromversorgungsgeräte haben ein Gewicht von
jeweils 6,6 kg. Seien Sie vorsichtig beim Umgang mit
dem Gerät, und vermeiden Sie, es fallenzulassen.

«
...
220
221
222
223
224
...
»

Содержание Passport 7400























































































































































































































































































































































































































































Отзывы:

Нет отзывов