Nortel Passport 7400 Скачать руководство пользователя страница 210 | Manualshive

Страница: 210 / 438

Nortel Passport 7400 Скачать руководство пользователя страница 210

210 Chapter 37 Hardware procedures

241-7401-240 5.2S1

Installing a 3-slot Passport switch in a seismic rack or
cabinet

Install a 3-slot Passport switch in a seismic rack or cabinet if you are located
in an earthquake zone.

Prerequisites

•

You will need a seismic rack-mount kit with PEC NTHQ20AA.

•

The seismic rack or cabinet must already be anchored and grounded. For
more information, see “Cabinet installation” (page 81).

•

If you plan to install a 3-slot Passport switch in a cabinet, check the
position and alignment of the vertical rails. Set the front rails 11.4cm (4.5
inches) from the front of the cabinet. Set the front and rear vertical rails
36.8 (14.5 inches) apart.

•

Install 13” termination panels prior to installing a 3-slot Passport switch
in a rack or cabinet.

Procedure steps

1

Attach the two rear brackets to the frame as shown in “Securing the rear
seismic brackets to the 3-slot Passport switch” (page 211).

2

Attach the front rack mount brackets to either side of the chassis as shown
in “Securing the rack-mounting brackets to the front vertical rails”
(page 212)

3

From the front of the cabinet, slide the 3-slot Passport switch into the rear
brackets and attach the front brackets to the chassis with the screws
provided. See the figure “Securing the rack-mounting brackets to the 3-
slot Passport switch” (page 208)

CAUTION

Risk of equipment damage

You need two people to install a 3-slot Passport switch
in a rack or cabinet: one person must hold the chassis in
place while a second person fastens the screws.

«
...
208
209
210
211
212
...
»

Содержание Passport 7400























































































































































































































































































































































































































































Отзывы:

Нет отзывов