Nortel Passport 4400 Series Скачать руководство пользователя страница 15

Страница: 15 / 144

Introduction

Passport 4400 Hardware Installation Manual

1-5

When working inside the unit, be sure to take all precautions against
electrostatic discharge:

• Wear a grounding strap to protect the equipment while the unit is open.

• To discharge any buildup of static electricity, touch any metal part of the

unit before handling any module.

• Avoid working on carpet.

Specifications

Note: Model numbers listed with a lowercase "x" indicate a revision

number for the selected model. For instance, model number
NTAU03xx represents all model numbers that begin with
NTAU03.

Base Unit

Physical Dimensions

3-slot Unit

Width

18 inches (45.7 cm)

Height

5 inches (12.7 cm)

Depth

12.75 inches (32.4 cm)

5-slot Unit

Width

18 inches (45.7 cm)

Height

7.75 inches (19.7 cm)

Depth

12.75 inches (32.4 cm)

5-slot Unit with Redundant Power Supply

Width

18 inches (45.7 cm)

Height

8.25 inches (21.0 cm)

Depth

12.75 inches (32.4 cm)

Warning:

WARNUNG, AVERTISSEMENT
Remove power plug from the power socket, or disconnect dc

power, before performing any service work on the unit.

Vor öffnen des Gerätes, muss der Netzstecker aus der

Steckdose gezogen werden.

Débrancher la prise de courant avant d’entreprendre aucun

travail de réparation de l’appareil.

Содержание Passport 4400 Series

















































































































































Результаты поиска

Содержание Passport 4400 Series

Отзывы:

Похожие инструкции для Passport 4400 Series

Бренды по названию

Популярные бренды

Nortel Passport 4400 Series, Руководство по установке оборудования

Результаты поиска

Содержание Passport 4400 Series

Отзывы:

Похожие инструкции для Passport 4400 Series

Бренды по названию

Популярные бренды