manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 96 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 96

96

Chapter 2 Using the console interface

320985-A Rev 01

 

The CI screens for your specific switch model display the model name in the main 
menu screen title and the correct number of ports and port types in the 

Port 

Configuration

 screen. 

Main menu

This section describes the options available from the CI main menu (

Figure 18

). 

The CI screens and submenus for these options are described in the following 
sections.

Note: 

The field values shown in the CI screens in this section are 

provided as examples only.

Note: 

Some menu options shown in this main menu example and in 

other screen examples in this chapter may not appear on your screen, 
depending on the switch options installed. However, the full menu 
options are shown in the screen examples and described in the following 
sections.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов