manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 69 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 69

Chapter 1 About Ethernet Switches 325 and 425

69

System Configuration Guide

 

Setting the unit as the Base Unit 

To set the unit as the Base Unit with the UI button:

1

Press the UI button and hold in for three seconds.

The unit is now in the Configuration mode, and the color and status of the UI 
LED turns green blinking.

2

Press the UI button once.

The Base LED turns on, and the Up and Down LEDs are steady green to 
indicate that the button press was recognized.

3

Press the UI button and hold it for three seconds to confirm the command.

The color and status of the UI LED returns to green once the command has 
been accepted.

If the command is rejected, the UI LED turns amber blinking. 

Setting the unit as the non-base unit

To set the unit as a non-base unit using the UI button:

1

Press the UI button and hold it for three seconds.

The unit will now be in the Configuration mode, and the color and status of 
the UI LED turns green blinking.

2

Press the UI button twice.

The Base LED will be off, and the Up and Down LEDs are steady green.

3

Press the UI button and hold it for three seconds to confirm the command.

Note: 

Changing the Base Unit does not take effect until you restart the 

system.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов