Nortel 425-24T Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 488

Nortel 425-24T Скачать руководство пользователя страница 49

Chapter 1 About Ethernet Switches 325 and 425

49

System Configuration Guide

restore factory-default [-y]

where the

[-y]

parameter instructs the switch not to prompt for confirmation.

For more information, refer to

“Resetting the switch to default configuration” on

Ping enhancement

Release 3.6 software extends the ping capabilities of the device. Using the CLI,
you can now specify additional ping parameters, including the number of ICMP
packets to be sent, the packet size, the interval between packets, and the timeout.
You can also set ping to continuous, or you can set a debug flag to obtain extra
debug information.

For more information, see

“Pinging” on page 259

show interfaces config command

The

show interfaces config

CLI command displays the current operational

status of interfaces and provides supplementary information about the current port
settings for Spanning Tree Protocol.

For more information, see

“show interfaces config command” on page 284

Autosave enable/disable enhancement

Release 3.6 software extends the ability to set autosave enable/disable using the
Console Interface (Configuration File > Autosave Configuration) and Web-based
management (Configuration > Configuration File).

«
...
47
48
49
50
51
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов