manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 48 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 48

48

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

 

3

If the configurations cause no problems and switch connectivity is 
maintained, you can perform the following:

a

Save the current running configuration using the 

copy config nvram

, 

write mem, 

or

 save config

 command.

b

Since the new configuration is working properly, cancel the reload using 
the 

reload cancel 

command.

If you make an error when performing configurations in Step 2 that results in the 
loss of switch connectivity (for example, an error in the IP address mask, MLT 
configuration, or VLAN trunking), the 

reload 

command provides you with a 

safeguard: when the reload timer expires, the switch reboots to the last saved 
configuration, and connectivity is re-established. Therefore, you do not have to 
travel to the remote site to reconfigure the switch.

For more information, see 

“reload command” on page 136

.

show mac-address-table enhancement

The 

show mac-address-table

 CLI command provides the following new 

parameters: 

include/exclude 

<pattern>

. These new parameters allow you 

to filter the results of the command by displaying only those entries in the address 
table that include or exclude the specified pattern. The value for 

<pattern>

 must 

be a sequence of 1 to 6 bytes in hex, separated by dashes, for example: 

show mac-address-table port 1/1-5 address 

include 00-0E-45-23

For more information, see 

“show mac-address-table command” on page 144

.

restore factory-default command

The 

restore factory-default

 CLI command resets the switch or stack back 

to its default configuration. 

The syntax for the 

restore factory-default 

command is:

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов