Nortel 425-24T Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 488

Nortel 425-24T Скачать руководство пользователя страница 46

46

Chapter 1 About Ethernet Switches 325 and 425

320985-A Rev 01

SNMP trap port enhancement

The SNMP trap port enhancement allows you to configure the SNMP trap port.
The default SNMP trap port used for communicating with the trap receiver is port
162. You can now configure a different SNMP trap port using the following CLI
command:

snmp-server host <host-ip> [port <1-65535>]

{<community-string>|v2c <community-string>|

v3 {auth|no-auth|auth-priv} <username>}

For more information, see

Configuring and Managing Security for Nortel

Ethernet Switches 325 and 425, Software Release 3.6

(320988-A).

EAPoL with Guest VLAN

Prior to Release 3.6, EAP (802.1x) Authentication supported Port Based User
Access. At any time, only one user (MAC) could be authenticated on a port, and
the port could be assigned to only one Port-based VLAN. Only the MAC address
of the device/user that completed the EAP negotiations on the port had access to
that port for traffic. Any tagging of ingress packets would be to the PVID of that
port. This remains the default configuration.

With Software Release 3.6, EAP also allows Guest VLANs to be configured for
access to that port. Any active VLAN can be made a Guest VLAN.

For more information, see

Configuring and Managing Security for Nortel

Ethernet Switches 325 and 425, Software Release 3.6

(320988-A).

shutdown command

The

shutdown

CLI command allows you to safely shut down and power off the

switch. Once the

shutdown

command is initiated, the switch saves the current

configuration, allowing you to power off the switch within the specified time
period (1 to 60 minutes). If the switch is not powered off within the allotted time,
the switch performs a reset.

«
...
44
45
46
47
48
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов