manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 377 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 377

Chapter 11 Administering the switch using Web-based management

377

System Configuration Guide

 

Quick Start

The Quick Start feature allows the administrator of the Ethernet Switch 325/425 
to make the initial setup by consolidating multiple setup pages into a single page. 
The 

Quick Start

 screen will allow the administrator to configure the following 

information:

•

Switch/Stack IP address

•

Subnet mask

•

Default gateway

•

SNMP Read community

•

SNMP Write community

•

SNMP Trap IP addresses and communities (up to four)

•

New  default  VLAN

During the initial setup mode, all ports in the switch or stack are assigned to the 
new default VLAN.

A port-based Quick Start VLAN is created if the new default VLAN does not 
exist. All ports are removed from the current default VLAN and assigned to the 
Quick Start VLAN. The PVIDs for all ports are changed to the Quick Start 
VLAN. The Quick Start VLAN is also designated as the management VLAN.

To configure the initial settings using the Quick Start feature:

1

From the main menu, select 

Administration > Quick Start

. 

The 

Quick Start

 page is displayed 

(Figure 152)

.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов