manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 371 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 371

Chapter 10 Configuring ports using Device Manager

371

System Configuration Guide

 

Viewing and editing multiple port configurations

To view or edit the configurations of multiple ports:

1

Select the ports you want to edit.

Press 

Ctrl+left click

 the ports you want to view or configure. A yellow 

outline appears around the selected ports.

2

Do one of the following:

•

From the shortcut menu, choose 

Edit

.

•

From the Device Manager main menu, choose 

Edit > Port

.

•

From the shortcut menu, choose 

Edit

.

•

From the toolbar, click 

Edit

.

AdminSpeed

Set the port’s speed.

OperSpeed

The current operating speed of the port.

AutoNegotiationCapability

Specifies the port speed and duplex capabilities that a switch can support 
on a port, and that may be advertised by the port using auto-negotiation

AutoNegotiationAdvertisments

Specifies the port speed and duplex abilities to be advertised during link 
negotiation.

MltId

The MultiLink Trunk to which the port is assigned (if any).

IsPortShared

Specifies whether a port is shared. Multiple ports that are logically 
represented as a single port are shared. Only one shared port may be 
active at a time.

PortActiveComponent

Specifies the physical port components that are active for a shared port.

Note:

 When you edit multiple ports, some tabs are not available, and 

some tabs are available even though the options are not applicable. When 
the option does not apply for a given port, NoSuchObject is displayed.

Table 140   

Interface tab fields for a single port (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов