manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 360 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 360

360

Chapter 9 Configuring the switch using Device Manager

320985-A Rev 01

 

ASCII config file

To display the 

ASCII Config file

 tab:

➨

In the 

File System

 dialog box, click on the 

ASCII Config File

 tab.

The 

ASCII Config File 

tab 

(Figure 145)

 opens.

Action

•

This object is used to download or upload a config file, an image 
file or diag firmware file. In read operation, if there is no action 
taken since the boot up, it will return with a value of other. 
Otherwise, it will return the latest action.

•

In a write operation, the values that can be written are: 

dnldConfig

dnldImg

upIdConfig

dnldFw

dnldImgIfNewer

dnldImgNoReset

dnldFwNoReset

•

The newly downloaded config, image or diag file will not take effect 
until the next boot cycle of the device.

Status

This object is used to get the status of the latest action as shown by 
s5AgInfoFileAction. The values that can be read are:

•

other — if no action taken since the boot up

•

inProgress — the operation is in progress

•

success — the operation succeeds

•

fail — the operation failed

Table 135   

FileSystem Config/Image/Diag file dialog box fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов