manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 345 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 345

Chapter 9 Configuring the switch using Device Manager

345

System Configuration Guide

 

AuthenticationTraps

Click to enable or disable. When you enable, SNMP traps 
are sent to trap receivers for all SNMP access 
authentication. When you disable, no traps are received.

To view traps, click the Trap toolbar button.

ReBoot

By default, the switch will be in the Running mode. The 
reboot command initiates a hardware reset.

AutoPVID

Click to enable or disable. When you enable, AutoPVID is 
activated. When you disable, AutoPVID is inactivated.

NextBootMgmtProtocol 

The transport protocol(s) to use after the next boot of the 
agent.

CurrentMgmtProtocol

The current transport protocol(s) that the agent supports.

BootMode

This setting determines how the management interface of

the switch will be assigned an IP address, the next time the

switch boots. The four BootMode options are:

•

local - use the IP address contained in the configuration 
file.

•

net - always attempt to get an IP address from the 
network.

•

netWhenNeeded - attempt to get an IP address from the 
network only when one is not contained in the 
configuration file.

•

netOrLastAddress - attempt to get an IP address from 
the network and if that fails use the IP address that was 
in use on this switch before the last reboot.

ImageLoadMode

The source from which the agent image is loaded at the 
next boot.

CurrentImageVersion

The version number of the agent image that is currently 
used on the switch.

LocalStorageImageVersion

The version number of the agent image that is stored in 
flash memory on the switch.

NextBootDefaultGateway

The IP address of the default gateway for the agent to use 
after the next time the switch is booted.

CurrentDefaultGateway

The IP address of the default gateway that is currently in 
use.

Table 129   

System tab fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов