manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 33 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 33

33

System Configuration Guide

 

Preface

This guide provides information about configuring and managing basic switching 
features on the Nortel Ethernet Switch 325 and Nortel Ethernet Switch 425.

This guide describes the features of the following Nortel switches.

•

Nortel Ethernet Switch 325-24T

•

Nortel Ethernet Switch 325-24G

•

Nortel Ethernet Switch 425-24T

•

Nortel Ethernet Switch 425-48T

The term “Ethernet Switch 325/425” is used in this document to describe the 
features common to the switches mentioned above. 

The term “Ethernet Switch 325” is used to describe features of the Ethernet 
Switch 325-24G and Ethernet Switch 325-24T collectively. 

Similarly the term “Ethernet Switch 425” is used to describe the features of the 
Ethernet Switch 425-24T and the Ethernet Switch 425-48T collectively.

A switch is referred to by its specific name while describing a feature exclusive to 
the switch.

You can use the Ethernet Switch 425-24T and the Ethernet Switch 425-48T in the 
standalone and stack configuration mode. The Ethernet Switch 325 operates only 
in the standalone mode.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов