manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 236 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 236

236

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

WEB Access

Specifies if access to the Web-based management system is allowed and only to those 
on the list.

Default value

Access: Enabled; Use List: Yes

Range

Access: Enabled, Disabled; Use List: Yes, No

Login Timeout

Specifies the amount of time a user has to enter the correct password at the 
console-terminal prompt.

Default value

1 minute

Range

0 to 10 minutes (0 indicates “no timeout”)

Login Retries

Specifies the number of times a user can enter an incorrect password at the 
console-terminal prompt before terminating the session.

Default value

3

Range

1 to 100

Inactivity 
Timeout

Specifies the amount of time the session can be inactive before it is terminated.

Default value

15 minutes

Range

0 to 60 minutes (0 indicates “no timeout”)

Event Logging

Specifies the types of events that are displayed in the Event Log screen (see 

System 

Monitoring Guide for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A).

Default value

All

Range

All, None, Accesses, Failures

Description

All:

 Logs the following Telnet events to the Event Log screen:

•

TELNET connect: Indicates the IP address and access mode of a 
Telnet session.

•

TELNET disconnect: Indicates the IP address of the remote host 
and the access mode, due to either a logout or inactivity.

•

Failed TELNET connection attempts: Indicates the IP address of 
the remote host whose IP address is not on the list of allowed 
addresses, or indicates the IP address of the remote host that did 
not supply the correct password.

None:

 Indicates that no Telnet events are logged in the Event Log 

screen.

Accesses

: Logs only Telnet connect and disconnect events in the 

Event Log screen.

Failures:

 Logs only failed Telnet connection attempts in the Event Log 

screen.

Table 52   

TELNET/SNMP/Web Access Configuration screen fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов