manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 232 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 232

232

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

Renumber Stack Units screen

The

 Renumber Stack Units 

screen (Figure 75) allows you to renumber the units 

configured in the stack. When selected, this option identifies the unit number of 
each unit in the stack configuration by lighting the corresponding number of (100 
Mb/s port) LEDs on each unit for approximately 10 seconds. For example, unit 3 
displays three LEDs.

To open the 

Renumber Stack Units 

screen:

➨

Choose 

Renumber Stack Units

 (or press 

n

) from the main menu.

Figure 84   

Renumber Stack Units screen.

Note: 

This menu option and screen appears only when the switch is 

participating in a stack configuration.

                             Renumber Stack Units 
 
 
  Current Unit Number              MAC Address           New Unit Number 
  -------------------    ----------------------------    --------------- 
        [  1  ]                00-60-fd-77-a6-0c              [  1  ] 
        [  2  ]                00-60-fd-77-a5-f0              [  2  ] 
        [  3  ]                00-60-fd-77-a4-4c              [  3  ] 
        [  4  ]                00-60-fd-77-ab-84              [  4  ] 
 
 
 
Renumbering stack units will cause an automatic Reset to Current Settings to 
occur across the entire stack.  The current configuration will be adapted to 
the new numbering scheme. Check the stack configuration after the reset to 
confirm the desired configuration is set. 
 
Are you sure you want to renumber switches with the new settings?   [ No  ] 
 
 
 
Use space bar to display choices, press <Return> or <Enter> to select choice. 
Press Ctrl-R to return to previous menu.  Press Ctrl-C to return to Main Menu. 

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов