manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 218 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 218

218

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

•

If the switch does not receive a BootP reply, the switch cannot be managed 
using the in-band IP address set from the console terminal.

If an IP address is not currently in use, these actions take effect immediately. If an 
IP address 

is

 currently in use, these actions take effect only after the switch is reset 

or power cycled.

BootP Disabled

This option allows you to manage the switch by using the IP address set from the 
console terminal. The Ethernet Switch 325/425 operates in the BootP Disabled 
mode as described in the steps below:

•

The switch does not broadcast BootP requests, regardless of whether an IP 
address is set from the console terminal.

•

The switch can be managed only by using the in-band switch IP address set 
from the console terminal.

BootP or Last Address

This option allows you to manage the switch even if a BootP server is not 
reachable. The Ethernet Switch 325/425 operates in the BootP or Last Address 
mode as described in the steps below:

•

When you specify the IP data from the console terminal, the IP address 
becomes the in-band address of the switch. BootP requests are not broadcast. 
You can manage the switch using this in-band IP address.

•

When you do not specify the in-band IP address from the console terminal, 
the switch broadcasts BootP requests until it receives a BootP reply 
containing an in-band IP address. If the switch does not receive a BootP reply 
that contains an in-band IP address within 10 minutes, the switch uses the last 
in-band IP address it received from a BootP server. This IP information is 
displayed in the Last BootP column.

If the IP address specified as the in-band IP address is

 

not currently in use, these 

actions take effect immediately. If an IP address is currently in use, 

these actions

 

take effect only after the switch is reset or power cycled.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов