manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 216 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 216

216

Chapter 6 System configuration using the Console Interface

320985-A Rev 01

 

Choosing a BootP request mode

The 

BootP Request Mode

 field in the 

IP Configuration

 screen allows you to 

choose which method the switch uses to broadcast BootP requests:

•

BootP When Needed

•

BootP  Always

•

BootP Disabled

In-Band Subnet 
Mask

The subnet address mask associated with the in-band IP address shown on the screen 
(see In-Band Switch IP address field). Network routers use the subnet mask to 
determine the network or subnet address portion of a host’s IP address. The bits in the 
IP address that contain the network address (including the subnet) are set to 1 in the 
address mask, and the bits that contain the host identifier are set to 0.

Default Value

0.0.0.0 (no subnet mask assigned)

Range

Four-octet dotted-decimal notation, where each octet is represented 
as a decimal value, between 0 and 255, separated by a decimal 
point

Default Gateway

The IP address of the default gateway.

Default Value

0.0.0.0 (no IP address assigned)

Range

Four-octet dotted-decimal notation, where each octet is represented 
as a decimal value, between 0 and 255, separated by a decimal 
point

IP Address to 
Ping

The IP address of the network device you want to ping. This field is not required for the 
operation of the stack.

Default Value

0.0.0.0 (no IP address assigned)

Range

Four-octet dotted-decimal notation, where each octet is represented 
as a decimal value, between 0 and 255, separated by a decimal 
point

Start Ping

Pings the selected network device when you choose Yes.

Default Value

No

Range

No, Yes

Table 47   

IP Configuration/Setup screen fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов