Nortel 425-24T Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 488

Nortel 425-24T Скачать руководство пользователя страница 159

Chapter 4 Getting Started with Device Manager

159

System Configuration Guide

Installing JDM on UNIX or Linux

This section includes the following topics:

•

“Minimum requirements” on page 160

•

“Installing JDM on Linux from the CD” on page 161

•

“Installing JDM on Solaris from the CD” on page 160

•

“Installing JDM on HP-UX from the CD” on page 160

•

“Installing JDM on UNIX or Linux from the web” on page 161

Note:

JDM installation procedures are standardized across all platforms. In

addition, the required Java Runtime Environment (JRE) version 1.4.1 is part of
the JDM installation package and does not require a separate installation. The
bundled JRE is used with this JDM only, and does not affect other Java
applications on the same system.

Note:

With Solaris and HP-UX, certain OS patches are required for JRE and

JDM to function properly. Please consult SUN or HP to install the appropriate
OS patches before launching JDM.

Note:

UNIX and Linux systems are case-sensitive. Use lower-case to specify

file names, and check to ensure that directories are entered correctly.

«
...
157
158
159
160
161
...
»

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов