manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 132 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 132

132

Chapter 3 CLI Basics

320985-A Rev 01

 

logout command

The 

logout

 command logs you out of the CLI session and returns you to the 

Main Menu of the Console Interface (CI) menus 

(Figure 28)

. The syntax for the 

logout

 command is:

logout

The 

logout

 command is in all command modes. 

The 

logout

 command has no parameters or variables.

enable command

The 

enable

 command changes the command mode from User EXEC to privExec 

mode. The syntax for the 

enable

 command is:

enable

The 

enable

 command is in the exec command mode.

The 

enable

 command has no parameters or variables.

configure command

The 

configure

 command moves you to the Global Configuration (config) 

command mode and identifies the source for the configuration commands. The 
syntax for the 

configure

 command is:

configure {terminal|network}

The 

configure

 command is in the privExec command mode.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов