manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 120 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 120

120

Chapter 3 CLI Basics

320985-A Rev 01

 

•

“Basic navigation” on page 128

•

“Managing basic system information” on page 137

•

“Managing MAC address forwarding database table” on page 143

CLI command modes

Most CLI commands are available only under a certain command mode. The 
Ethernet Switch 325/425 has the following four command modes:

•

User EXEC

•

Privileged EXEC

•

Global Configuration

•

Interface Configuration

The User EXEC mode is the default mode; it is also referred to as exec. This 
command mode is the initial mode of access on powering-up the Ethernet Switch 
325/425. In this command mode, the user can access only a subset of the total CLI 
commands; however, the commands in this mode are available while the user is in 
any of the other four modes. The commands in this mode are those you would 
generally need, such as 

ping

 and 

logout

.

Commands in the Privileged EXEC mode are available to all other modes but the 
User EXEC mode. The commands in this mode allow you to perform basic 
switch-level management tasks, such as downloading the software image, setting 
passwords, and booting the Ethernet Switch 325/425. The Privileged EXEC mode 
is also referred to as privExec mode.

The Global Configuration mode and the Interface Configuration mode allow you 
to change the configuration of the Ethernet Switch 325/425. Changes made in 
these command modes are immediately applied to the switch configuration and 
saved to NVRAM.

The Global Configuration commands allow you to set and display general 
configurations for the switch, such as the IP address, SNMP parameters, the 
Telnet access, and VLANs. The Global Configuration mode is also referred to as 
config mode.

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов