manualshive.com logo in svg

Nortel 425-24T, Руководство по настройке, Страница: 105 / 488

Поделиться
Скачать
Nortel 425-24T Скачать руководство пользователя страница 105

Chapter 2 Using the console interface

105

System Configuration Guide

 

MultiLink Trunk Configuration...

Displays the 

MultiLink Trunk Configuration Menu

 (see 

Configuring VLANs, Spanning Tree, and MultiLink Trunking 
for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320986-A)). This menu provides the following options: 

MultiLink Trunk Configuration and MultiLink Trunk Utilization. This 
menu allows you to create and modify trunks, and to monitor the 
bandwidth utilization of configured trunks.

Port Mirroring Configuration...

Displays the

 Port Mirroring Configuration

 screen (see 

System 

Monitoring Guide for Nortel Ethernet Switches 325 and 425, 
Software Release 3.6

(320989-A)). This screen allows you to 

designate a single switch port as a traffic monitor for one specific port.

Rate Limiting Configuration

Displays the 

Rate Limiting Configuration 

screen (

“Rate Limiting 

Configuration screen” on page 115

). This screen allows you to limit 

the forwarding rate of broadcast and multicast packets at ingress.

IGMP Configuration

Displays the 

IGMP Configuration

 screen (

Configuring IP 

Multicast for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320990-A)). This screen allows you to optimize 

multicast traffic by setting up IGMP port memberships that filter 
multicast on a per port basis

Display Port Statistics

Displays the 

Port Statistics

 screen (see 

System Monitoring Guide 

for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A)). This screen allows you to view detailed 

information about any switch port.

Clear All Port Statistics

Allows you to clear all port statistics.

This option is followed by screen prompts that precede a choice of the 
actions:

•

If the switch is operating 

standalone

, choose one of the following:

•

Yes, to clear all port statistics for all switch ports

•

No, to abort the option

•

If the switch is 

participating in a stack configuration

, choose one of 

the following:

•

Clear all port statistics for a specific unit in the stack

•

Clear all port statistics for the entire stack

•

No, to abort the option

Table 16   

Switch Configuration Menu options (continued)

Option

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Отзывы:

Нет отзывов