Nortel 425-24T Скачать руководство пользователя страница 102

Страница: 102 / 488

102

Chapter 2 Using the console interface

320985-A Rev 01

MAC Address

The MAC address of the switch or, when the switch is participating in a stack
configuration, the MAC address of the stack configuration.

Reset Count

A read-only field that indicates the number of resets since the operational firmware
was first loaded on the switch.

Default Value

Range

0 to 2

-1 (4,294,967,295)

Last Reset Type

A read-only field that indicates the last type of reset.

Default Value

Power Cycle

Range

Power Cycle, Software Download, Management Reset,
Management Factory Reset

Power Status

A read-only field that indicates the current power source (primary, RPSU, or both).

Default Value

Primary Power

Range

Primary Power, Redundant Power, Primary and Redundant
Power

Local GBIC Type

A read-only field that indicates the GBIC type that is configured in this unit. (This field
is applicable only to the Ethernet Switch 425).

sysDescr

A read-only field that specifies hardware and software versions.

sysObjectID

A read-only field that provides a unique identification of the switch, which contains
the vendor’s private enterprise number.

sysUpTime

A read-only field that shows the length of time since the last reset. Note that this field
is updated when the screen is redisplayed.

sysNtpTime

A read-only field that displays the current date and time and the configured time
offset from Universal Coordinated Time (UTC).

sysServices

A read-only field that indicates the switch’s physical and data link layer functionality.

sysContact

The name and phone number of the person responsible for the switch.

Default Value

Zero-length string

Range

Any ASCII string of up to 56 printable characters

sysName

A name that uniquely identifies the switch.

Default Value

Zero-length string

Range

Any ASCII string of up to 56 printable characters

sysLocation

The physical location of the switch.

Default Value

Zero-length string

Range

Any ASCII string of up to 56 printable characters

Table 15

System Characteristics screen fields (continued)

Field

Description

Содержание 425-24T









































































































































































































































































































































































































































































































Результаты поиска

Содержание 425-24T

Отзывы:

Nortel 425-24T, Руководство по настройке, Страница: 102 / 488

Результаты поиска

Содержание 425-24T

Отзывы: