manualshive.com logo in svg

Nortel 1002rp, Техническое обслуживание и диагностика

Поделиться
Скачать
Nortel 1002rp Скачать руководство пользователя страница 95

January 2007

Using CallPilot system utilities

1002rp Server Maintenance and Diagnostics

95

Diagnostics Tool

The Diagnostics Tool allows you to enable or disable CallPilot startup 
diagnostics. CallPilot startup diagnostics automatically identify 
hardware problems that may exist when the system and its services are 
started. When you disable startup diagnostics, you can save time during 
system maintenance operations where restarts or call processing services 
restarts are required. There are three recommended steps:

„

Use the Diagnostics Tool to turn off CallPilot startup diagnostics.

„

Perform system maintenance.

„

Use the Diagnostics Tool to turn on CallPilot startup diagnostics.

To access the Diagnostics Tool

On the Windows desktop, click Start 

➝

 Programs 

➝

 CallPilot 

➝

 

System Utilities 

➝

 Diagnostic Tool.

Result: 

The Diagnostics Tool window appears.

To enable startup diagnostics

From the Diagnostics Tool window, select Configuration 

➝

 Maintenance 

Startup Diag 

➝

 Enable.

To disable startup diagnostics

ATTENTION

Nortel recommends that you leave the startup 
diagnostics turned on. When you disable CallPilot 
startup diagnostics, you prevent CallPilot from 
automatically identifying hardware problems that may 
exist when the system and its services are started (for 
example, DSP, Time Switch, or Media Bus).

Содержание 1002rp



























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды