background image

1

GOCONTROL SMART LEAK DETECTOR

The GoControl™ family of Z-Wave® certifi ed wireless lighting products (smart 
LED bulbs, switches, dimmers, outlets, plug-in modules), security devices 
(alert sounder, motion sensor, and door/window sensor), and control products 
(garage door controller and thermostat) bring a new level of intelligent wireless 
capability to commercial and residential environments.

The Z-Wave wireless protocol is an international wireless standard for remote 
home automation, security and other applications. Embedded in each device, 
the Z-Wave smart chip enables two-way RF communication among hundreds 
of Z-Wave enabled devices, allowing products and services from multiple 
manufacturers to work seamlessly.

The WF00Z-1 Smart water detector is simple to set up and provides an alert 
when there is water present at specifi c high risk locations; water heater, under 
sinks washing machine.

GoControl Z-Wave products are easy to install, are Z-Wave Plus certifi ed, and 
allow dealers to create an integrated wireless network with nearly limitless 
expansion and interoperability with security, energy management, home 
entertainment, appliances, and more.

For indoor use only.

 Retain instructions for future use.

Z-WAVE PLUS FEATURES

The WF00Z-1 contains a Z-Wave 500 Series Module that supports 
Z-Wave Plus® features. A Z-Wave certifi ed portable or stationary Controller 
can communicate with the Z-Wave 500 Series Module.

Depending on the capability of the Controller or gateway software, the following 
operations will be performed by FloodZ. Refer to the controller or gateway 
manual for details.

•  Send an alert if water is present.
•  Add or Remove FloodZ.
•  Over-the-air firmware update by the gateway or static Controller.

INSTALLATION

The WF00Z-1 consists of the transmitter and a sensor that is connected to it 
by a 7 foot long wire. The sensor can attach to the fl oor or wall with the two 
screws (supplied).

1. 

Add the WF00Z-1 to a Z-Wave network (see reverse side).

2. 

Use two screws provided to attach the fl ood sensor to the fl oor or wall in the 
location where fl ooding is most likely to occur.

3. 

Use two screws or the double-stick tape supplied to attach the transmitter 
to the wall, above the sensor level.

 

NOTE: Position the WF00Z-1 in a location where it would not likely be 
affected by fl ooding or have its wireless signal blocked by metal appliances.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,WF00Z-1, GO CONTROL; P/N: 10008416 X6; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: FLAT 8.500” x 11.000”, FOLDED 4.250” x 2.750”; TOLERANCE ± .125”; SCALE: 1-1 PAGE 1 OF 2

WF00Z-1

Z-Wave Radio Frequency (RF) Controlled 

Flood Detector

NOTE: 

This unit must be added to the Network 

only where it will be permanently installed. 

The proper operation of this node in the 

mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this unit, then install.

WF00Z-1

T

R

AN

S

MITTE

R

FLOOD

S

EN

S

O

R

7-FOOT

CABLE

INDICATO

R

WF00Z-1

T

R

AN

S

MITTE

R

FLOOD

S

EN

S

O

R

ATTACH FLOOD

S

EN

S

O

R

 WITH

TWO 

S

C

R

EW

S

S

C

R

EW HOLE

S

 FO

R

WALL O

R

 FLOO

R

MOUNTIN

G

FLOO

R

ATTACH T

R

AN

S

MITTE

R

WITH TWO 

S

C

R

EW

S

O

R

 ADHE

S

IVE TAPE

Z-Wave® and Z-Wave Plus® are registered trademarks of Sigma Designs and 
its subsidiaries in the United States and other countries.
Covered by one or more claims of patents: http://sipcollc.com/patent-list/ 
and http://intusiq.com/patent-list/
Terms and Conditions pertaining to the sale of this Nortek Security & Control 
wireless mesh network product are available at 
http://nortekcontrol.com/terms_conditions.php

Отзывы: