2GIG-DW40-345
WIRELESS DOOR/WINDOW CONTACT WITH LOCAL BYPASS
INSTALLATION INSTRUCTIONS
1. The Wireless Door/Window Contact with Local Bypass
(2GIG-DW40-345) is designed for installa on on doors,
windows, and other items having an open/close feature.
It communicates with the control panel using the 2GIG
protocol.
2. Figure 1.
Wireless Door Contact Components
Box Contents
Verify that the package contains the following:
• 1—Wireless Door/Window Sensor with Ba ery
• 1—Adhesive Tape for Sensor
• 1—Magnet
• 1—Adhesive Tape for Magnet
• 2—Phillips Screws
Activating Contact
To ac vate the ba ery in contact, pull out the plas c ba ery
pull tab and discard it. A red LED will
fl
ash 5 mes to indicate
that the bypass bu on is enabled.
Figure 2.
Removing the Plastic Battery Pull Tab
Mounting Orientation
Before moun ng the contact and magnet
check
the moun ng
orienta on (See Figure 3). There are three (3) lines on the
contact and they
must
face the magnet.
Figure 3.
Contact/Magnet Orientation
CONTACT
MAGNET
3 LINES
MUST FACE
MAGNET
5/8”
MAX.
HIDDEN
LED
5/8”
MAX.
RIGHT MOUNTED
CONTACT
LEFT MOUNTED
CONTACT
Mount the contact
on the sta onary part of the window or door.
Mount the magnet on the moving part of the window or door.
A 5/8”(15.875mm) maximum distance is allowed between the
magnet and contact.
Figure 4.
Contact/Magnet Location on a Window or Door
Contact Mounting Methods
First determine if the local bypass bu on will be used. The
local bypass bu on is enabled by default. Disabling the bu on
provides higher security if used as a door/window contact only.
Please see reverse side on instruc ons to enable or disable the
local bypass bu on.
Select the moun ng method that will be used. If the installa on
conforms to UL, open the contact base using a coin in the slots
(See Figure 5). Fasten the contact base permanently to loca on
using the Phillips screws (provided). See Figure 6.
Figure 5.
Opening Contact
Figure 6.
Permanently Mounting Contact Base
Figure 7.
Double-Stick Tape Mounting Contact & Magnet
If installa on is not for a UL installa on, the contact can be
fastened into posi on using double-s ck tape. (See Figure 7).
1. Clean and dry the surface of the moun ng loca ons.
2. Apply the adhesive strips to the contact and magnet.
3. Use
fi
rm pressure to adhere the contact to the desired
loca on. NOTE: For best results, avoid moun ng the
adhesive tape at temperatures below 50
°
F (10
°
C). A er
24 hours, bond will hold at lower temperatures.
ADHESIVE STRIP
FOR MAGNET
MAGNET
ADHESIVE STRIP
FOR CONTACT
CONTACT
PHILLIPS
SCREWS (2)
PULL & DISCARD
BEFORE USE
PLASTIC
BATTERY PULL
TAB
CONTACT
CONTACT
COIN
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,2GIG-DW40-345 - P/N: 10005518 X12 - INK: BLACK - MATERIAL: 16 LB. MEAD BOND - SIZE: 6.000" X 8.000" - TOL. +/- 0.125”- SCALE: 1-1 - FOLDING: 4X TO 1.5" x 2" SIDE 1 OF
2
CONTACT BASE
PHILLIPS
SCREWS
CONTACT IS ATTACHED
TO STATIONARY LOCATION
MAGNET
MAGNET
REMOVE BACKING
MAGNET
CONTACT
DOUBLE-STICK TAPE
DOUBLE-STICK
TAPE
