Nortek Security & Control 2GIG Z-Wave Plus, Руководство пользователя

Страница: 10 / 17

Copyright © 2020 Nortek Security & Control 17 16 Copyright © 2020 Nortek Security & Control
Clock Menu
Use the clock menu to set thermostat’s internal clock.
Figure 17. Clock Setup
Setting the Clock
1. Touch any button to take thermostat out of sleep mode.
2.
Touch
MODE
button for 5 seconds until,
SETUP
appears in status display line.
3. Use

buttons to select CLOCK in status display line.
4. Touch FAN (Select). DAY will be displayed
5. Touch the

buttons. TIME will be displayed.
6. Use the

buttons to select the current time.
7. Choose
FAN (Select)
, MODE (Done) , MODE (Done) .
INFO Menu
The INFO menu displays information about the thermostat. Use the

buttons to scroll through
the various items.
• MODEL 2GIG-STZ-1
•
VERSION Thermostat firmware version.
• Z-WAVE Z-Wave firmware version.
• SYSTEM TYPE displays current System Type setting.
• If System Type = Standard, FAN TYPE displays current Fan Type setting.
• If System Type = Heat Pump, CHANGEOVER TYPE displays current Change Over setting.
• Battery xx% = Battery Level (If battery powered)
If the thermostat is included in a Z-Wave network, items below will be present.
• Z-Wave Node ID Node ID of Z-Wave Network
• Z-Wave Home ID Home ID of Z-Wave Network
Factory Reset
WARNING: Please use this procedure only when the Z-Wave Primary Controller is
missing or otherwise inoperable .
To reset the 2GIG-STZ-1 's Z-Wave parameters to Factory Settings (both Z-Wave and HVAC settings):
8. Touch and hold MODE button to go to Setup menu.
9. Touch and hold MODE and the down arrow key (

) to enter Advanced Menu.
10. Navigate to Restore Defaults to perform a factory reset.
Advanced System Settings Menu
The Advanced System Settings Menu provides for addition system setup options. These settings can
affect system operation and should only be changed by qualified HVAC installers.
To access the Advanced System Settings menu, first touch and hold the
MODE button to get into the
Setup menu. While in the Setup Menu, touch and hold both the MODE and

buttons for 5 seconds.
• Use the

buttons to scroll through the menu options to the desired setting.
• Touch FAN (Select) to change a setting. Once it begins to flash, use the

buttons to select
the desired setting.
• Touch FAN (Select) to accept the new setting (flashing will stop). Select MODE (Done) to exit
the option and return to the SETUP screen.
Feature Description Range
Test Mode
Temporary shorten Minimum Run Time,
Minimum Off Time to 10 seconds for fast testing.
Y or N
Frost Protection Enable
When enabled, frost protection activates at 41 °F
(5 °C) and stops at 47 °F (8 °C) regardless of System
Mode and Heat / Cool Set Point.
Y or N
Aux Heat Enable
(Heat Pump System Only)
Use Auxiliary Heater as 2nd / 3rd Stage Heater. Y or N
2nd Stage Heat Enable Enables the second stage heat operation Y or N
3rd Stage Heat Enable
(Standard System Only)
Enables the third stage heat operation Y or N
2nd Stage Cool Enable Enables the second stage cool operation Y or N
Compressor in Heat
Stage 3
(Heat Pump System Only)
Set
No
to disable compressor in Heat Stage 3 for
energy saving.
Y or N
Minimum Run Time
Minimum Run Time before a heating / cooling
cycle can turn off.
1 – 9 minutes
Minimum Off Time
Minimum Off Time before a heating / cooling
cycle can begin.
5 – 9 minute
Heat Set point Max Maximum Set point value of Heat Mode
32 – 90 °F
(0 – 32 °C)
Cool Set point Max Maximum Set point value of Cool Mode
61 – 122 °F
(16 – 50 °C)
Heat Blower Off Delay
System blower delay off time after a heat call
ends
0 – 90 seconds
Cool Blower Off Delay
System blower delay off time after a cool call
ends
0 – 90 seconds
Heat-Cool Delta
Minimum separation between Heating and
Cooling Set point
36-48°F (2 – 9 °C)
Heat Stage 1 on Threshold Delta from Set point that stage 1 heating start 34 - 45°F (1 - 7°C)
Heat Stage 1 off Threshold Delta from Set point that stage 1 heating off 32 - 45°F (0 – 7 °C)
Heat Stage 2 on Threshold
Delta from Set point that stage 2 heating start
(This will be Aux Stage on Threshold, if Aux Heat
Enable & 2nd Stage Heat not Enable in Heat
Pump System)
36 - 46°F (2 – 8 °C)
TOUCH AND HOLD
FOR 5 SECONDS
TOUCH THE
▲▼
BUTTONS TO CHANGE
TO THE DESIRED MENU
ITEM, THEN TOUCH
FAN (Select)
MENU CHOICES ARE DISPLAYED IN THE
STATUS DISPLAY LINE
Select
Done
CLOCK