16
ASA18V
EN
The drill is fitted with auto spindle lock which means if
you try to rotate the chuck by hand the spindle will au-
tomatically lock. This means you only need to grasp the
chuck and rotate the chuck housing to remove or fit ac
-
cessories.
▪
Hold the machine with one hand and rotate the chuck
with the other hand.
- To open the chuck, rotate it anti-clockwise. (B)
- To close the chuck, rotate it clockwise. (D)
▪ Insert the bit. (C)
▪ Close the chuck.
▪
Perform a test run to check that the bit is properly
clamped in the centre.
REPLACING THE CHUCK
WARNING:
Replacing the chuck must be per-
formed only in authorised service centres. Please do
not attempt to replace the chuck with available tools
otherwise you may damage the cordless drill/driver.
DRILLING
Drilling metal
▪
For maximum performance, use high speed steel bits
for drilling in metal or steel.
▪ Ensure that the torque adjustment collar (9) is at posi
-
tion “drill bit”.
▪
Begin drilling at very low speed to prevent the bit from
slipping off the starting point.
▪
Always clamp sheet metal.
▪
Support thin metal with a block of wood to avoid dis-
torting it.
▪
Use a punch to mark the centre of the hole.
▪
Use a suitable lubricant for the material you are work-
ing on.
Material
Lubricant
Steel
Oil
Aluminium
Turpentine or paraffin
Brass, copper or cast iron
Do not lubricate
Drilling plastics and plastic coated chipboard
▪
Use high speed drill bits.
▪ Refer to “Drilling wood” below.
Drilling wood
▪
For maximum performance, use high speed steel bits
for wood drilling.
▪ Ensure that the torque adjustment collar (9) is at posi
-
tion “drill bit”.
▪
Begin drilling at very low speed to prevent the bit from
slipping off the starting point. Increase the speed as
the drill bites into the material.
▪
When drilling through holes, place a block of wood
behind the work piece to prevent ragged or splintered
edges on the back side of the hole.
All drilling operations
▪
Use only sharp drill bits.
▪
Mark off the centre of the hole using a centre punch
or nail.
SCREWING / UNSCREWING
Select the appropriate torque by placing one of the num-
bers, marked on the torque adjustment collar (9), against
the arrow on the tool housing.
Insert the necessary bit.
WARNING:
Over-tightening can result in the
screw breaking or damage to the end of the driver bit.
WARNING:
If the machine is held at an angle
to the screw being tightened, the head of the screw
may be damaged, or the specified torque may not be
transmitted to the screw. Always keep the machine
and the screw being tightened in a straight line.
Maintenance
WARNING:
Always set the forward/reverse
switch (3) in central position before any work on the
machine e. g. fitting and removing a battery, tool
change, transport, maintenance and storage.
Regularly check that all the fixing screws are tight. They
may vibrate loose over time.
CLEANING
For safe operation always keep the machine and its ven-
tilation slots clean.
Regularly check to see if any dust or foreign matter has
entered the grills near the motor and around the switch-
es. Use a soft brush to remove any accumulated dust.
Wear safety glasses to protect your eyes whilst cleaning.
If the body of the tool needs cleaning, wipe it with a soft
damp cloth. A mild detergent can be used.
WARNING:
Never use alcohol, petrol or other
cleaning agent. Never use caustic agents to clean
plastic parts.
WARNING:
Water must never come into con-
tact with the tool.
CHARGER CLEANING INSTRUCTIONS
WARNING:
Disconnect the charger from the
AC outlet before cleaning.
▪
Dirt and grease may be removed from the exterior of
the charger using a cloth or soft non-metallic brush.
Do not use water or any cleaning solutions.
Содержание ASA18V
