Nordson Trilogy GP Скачать руководство пользователя страница 15

Страница: 15 / 21

Trilogy

GP Air Spray and LVLP Gravity Fed Manual Spray Guns

1601056-05

Troubleshooting

WARNING:

Allow only qualified personnel to perform the following tasks. Follow the

safety instructions in this document and all other related documentation.

If you need help to solve a problem with your spray gun, contact your Nordson

representative or call the Industrial Coating Systems Customer Support Center at

(800) 433−9319. See

Figure 3 for service parts.

Problem

Possible Cause

Corrective Action

1. Irregular Pattern

Air cap not tightened correctly or dirty

Check air cap (2), clean if necessary.

Fluid nozzle installed incorrectly

Check fluid nozzle (4).

Fluid nozzle not tightened correctly

Tighten fluid nozzle.

Fluid nozzle cracked at orifice

Replace fluid nozzle.

2. Paint leaking from

packing gland

Packing gland not tightened correctly

Tighten packing gland (23) gradually until

leaking stops.

Needle seals worn

Replace seals (18, 19).

3. Pain dripping from

nozzle

Fluid nozzle loose, cracked, or worn

Tighten nozzle (4), replace nozzle if cracked

or worn.

Needle seals worn

Replace seals (18, 19).

Needle pressure spring weak

Replace spring (25).

4. Spray gun leaking air

Air seal or valve is worn

Replace seal (14) and air valve (15).

5. Spray gun leaking air

from fan adjustment

screw

Fan adjustment screw worn

Replace fan adjustment screw (12).

Содержание Trilogy GP






















Результаты поиска

Содержание Trilogy GP

Отзывы:

Бренды по названию

Популярные бренды

Nordson Trilogy GP, Руководство пользователя по изделию

Результаты поиска

Содержание Trilogy GP

Отзывы:

Бренды по названию

Популярные бренды