manualshive.com logo in svg

Nordson Trilogy GP, Руководство пользователя по изделию

Поделиться
Скачать
Nordson Trilogy GP Скачать руководство пользователя страница 14

10

Trilogy

®

 GP Air Spray and LVLP Gravity Fed Manual Spray Guns

© 2021 Nordson Corporation

1601056-05

Maximum Inlet Air Pressure for LVLP Compliance

The following table provides air pressure settings to use as approximate starting points. 

The results can vary; use your compliance kit to ensure that the air output from your 

spray gun does not exceed 0.69 bar (10 psi).

Size

Pattern 

Setting

Inlet Pressure

Air Cap Atomizing 

Pressure

At Gun

At Regulator (A)

A

Flat

1.9 bar (27.5 psi)

1.8 bar (25.5 psi)

0.69 bar (10 psi)

Round

1.7 bar (25 psi)

2.3 bar (32.5 psi)

0.69 bar (10 psi)

A1

Flat

1.9 bar (27.5 psi)

2.2 bar (32 psi)

0.69 bar (10 psi)

Round

1.8 bar (25.5 psi)

1.8 bar (26 psi)

0.69 bar (10 psi)

B

Flat

2.3 bar (33 psi)

2.6 bar (37 psi)

0.69 bar (10 psi)

Round

2.6 bar (38 psi)

2.9 bar (41.5 psi)

0.69 bar (10 psi)

C

Flat

2.6 bar (37.5 psi)

2.8 bar (41 psi)

0.69 bar (10 psi)

Round

5.2 bar (76 psi)

5.3 bar (77.5 psi)

0.69 bar (10 psi)

D

Flat

2.5 bar (37 psi)

2.9 bar (42.5 psi)

0.69 bar (10 psi)

Round

6.0 bar (88 psi)

6.3 bar (91 psi)

0.69 bar (10 psi)

NOTE:  A.  Pressure readings at regulator made using 50 ft of 3/8 in. hose.

Cleaning

1. Flush the spray gun as described on page 6.
2. Relieve the air pressure.
3. 

Remove the air cap and clean the fluid nozzle with the supplied cleaning brush and 

solvent or waterborne cleaning solution compatible with the paint you are using.

NOTE:  

Use only properly sized tools designed for nozzle cleaning to clean the nozzle 

orifice. Contact your Nordson representative for nozzle cleaning kits.

Lubrication

See Figure 4. The trigger pin (18), valve pin (12B), and paint needle (6) should be 

lubricated with silicone-free oil daily.

Содержание Trilogy GP






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды