Nordson PermaFlo 830 Скачать руководство пользователя страница 45

Страница: 45 / 102

Air Motor Repair

C 1-2

Part 1022914G03

2007 Nordson Corporation

Guidelines for O-ring and Seal Replacement

CAUTION:

When removing O-rings and seals from grooves, use a tool that

will not scratch the machined surfaces of the grooves. Scratches can cause

leaks.

When rebuilding the air motor, replace all seals and O-rings. Lubricate all

O-rings and seals with MagnaLube-G or equivalent PTFE-impregnated

grease as instructed.

Coupling Removal and Replacement

CAUTION:

Do not scratch or score the connecting rod. Any burrs will

damage the U-cup seal and cause it to leak.

Coupling Removal

1. Stop the air motor in the middle of a stroke. Shut off the air supply to the

pump and disconnect the air supply hose from the air valve.

2. See Figure C 1-1. Loosen the two set screws (32) in the coupling

sleeve (33) with a

-in. hex wrench.

3. Slide the coupling sleeve up the connecting rod (21) and remove the two

coupling halves (34) from the rod and plunger (A). Tap upward on the

sleeve with a rubber mallet to loosen it, if necessary.

4. Push the connecting rod up away from the plunger and remove the

coupling sleeve.

1300386A

Tighten to 10.2

1 N

(90

10 in.-lb)

when re-installing

coupling.

Figure C 1-1

Coupling Removal and Replacement

21. Connecting rod
32. Set screws

33. Coupling sleeve

34. Coupling halves

A. Plunger

Содержание PermaFlo 830







































































































Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды

Nordson PermaFlo 830, Руководство пользователя по изделию

Результаты поиска

Содержание PermaFlo 830

Отзывы:

Похожие инструкции для PermaFlo 830

Бренды по названию

Популярные бренды