Nordson PermaFlo 815 Скачать руководство пользователя страница 70

Страница: 70 / 99

Hydraulic Section Repair

C 2-13

Part 1102698

−

2019 Nordson Corporation

Siphon Housing Assembly

1. See Figure C 2-12. Loosen the pressure housing (8) from the

soft-jawed vise and position horizontally in the soft-jawed vise.

2. Lubricate the new PTFE O

−

ring (13), located below the ball seat, with

O-ring lubricant. Install the PTFE O-ring (13), siphon ball seat (12),

large ball (11), and cage (10) into the siphon housing.

3. Lubricate the threads of the pressure housing and the siphon housing

with O-ring lubricant. Thread the siphon housing (14) onto the pressure

housing (8) and tighten hand tight. Remove the pressure housing from

the soft-jawed vise.

Figure C 2-12 Siphon Housing Assembly

8. Pressure housing

10. Cage

11. Ball (large)

12. Siphon ball seat
13. O-ring (white PTFE)
14. Siphon housing

Содержание PermaFlo 815




































































































Результаты поиска

Содержание PermaFlo 815

Отзывы:

Похожие инструкции для PermaFlo 815

Бренды по названию

Популярные бренды

Nordson PermaFlo 815, Руководство пользователя

Результаты поиска

Содержание PermaFlo 815

Отзывы:

Похожие инструкции для PermaFlo 815

Бренды по названию

Популярные бренды