Nordson PermaFlo 815 Скачать руководство пользователя страница 59

Страница: 59 / 99

Hydraulic Section Repair

C 2-2

Part 1102698

−

2019 Nordson Corporation

Guidelines for O-ring and Seal Replacement

CAUTION:

When removing O-rings and seals from grooves, do not scratch

the machined surfaces of the grooves. Scratches can cause leaks.

When rebuilding the hydraulic section, replace all seals and O-rings.

Lubricate all O-rings and packing V-rings with Parker O-Lube or equivalent

O-ring lubricant.

Coupling Removal and Replacement

CAUTION:

Do not scratch or score the connecting rod. Any burrs will

damage the U-cup seal and cause it to leak.

Coupling Removal

1. Stop the air motor in the middle of a stroke and disconnect the air supply

hose from the air valve.

2. See Figure C 2-1. Loosen the two set screws (B) in the coupling

sleeve (A) with a

-in. hex wrench.

3. Slide the coupling sleeve up the connecting rod (C) and remove the two

coupling halves (D) from the rod and plunger (8). Tap upward on the

sleeve with a rubber mallet to loosen it, if necessary.

4. Push the connecting rod up away from the plunger and remove the

coupling sleeve.

Tighten to 10.2

1 N

(90

10 in.-lb)

when re-installing

coupling.

Figure C 2-1

Coupling Removal and Replacement

4. Plunger

A. Coupling sleeve
B. Set screws

C. Connecting rod
D. Coupling halves

Содержание PermaFlo 815




































































































Результаты поиска

Содержание PermaFlo 815

Отзывы:

Похожие инструкции для PermaFlo 815

Бренды по названию

Популярные бренды

Nordson PermaFlo 815, Руководство пользователя

Результаты поиска

Содержание PermaFlo 815

Отзывы:

Похожие инструкции для PermaFlo 815

Бренды по названию

Популярные бренды