Nordson PermaFlo 815 Скачать руководство пользователя страница 51

Страница: 51 / 99

Air Motor Repair

C 1-8

Part 1102698

−

2019 Nordson Corporation

Air Motor Re-Assembly

Clean all reusable parts thoroughly before re-assembling the air motor.

Inspect all parts and replace any that are worn, scored, or damaged beyond

repair.

Piston/Connecting Rod Assembly

See Figure C 1-6.

1. Thread the new piston (22) counterclockwise (left-hand threads) onto

the connecting rod (21) until the piston contacts the shoulder at the

bottom of the connecting rod threads.

2. Install the flat washer (23) on the socket-head screw (24), and thread

the screw into the connecting rod. Tighten the screw to 27

4 N

(20

3 ft-lb).

Tighten to 27

4 N

(20

3 ft-lb)

Left-hand threads: Turn

clockwise to loosen,

counterclockwise to tighten.

Tighten

Figure C 1-6 Piston/Connecting Rod Assembly

21. Connecting rod
22. Air piston

23. Flat washer
24. Socket-head screw

Содержание PermaFlo 815




































































































Результаты поиска

Содержание PermaFlo 815

Отзывы:

Похожие инструкции для PermaFlo 815

Бренды по названию

Популярные бренды

Nordson PermaFlo 815, Руководство пользователя

Результаты поиска

Содержание PermaFlo 815

Отзывы:

Похожие инструкции для PermaFlo 815

Бренды по названию

Популярные бренды