Nordson PermaFlo 815 Скачать руководство пользователя страница 58

Страница: 58 / 99

Hydraulic Section Repair

C 2-1

Part 1102698

−

2019 Nordson Corporation

Section C 2

Hydraulic Section Repair

WARNING:

Allow only qualified personnel to perform the following tasks.

Follow the safety instructions in this document and all other related

documentation.

WARNING:

Shut off and lock out the compressed air supply to the pump

and relieve system fluid pressure before servicing the pump or other system

components. Failure to observe this warning may result in serious injury.

Introduction

This section contains procedures for:

Coupling removal and replacement

Hydraulic section rebuild

NOTE:

Part numbers in illustrations match the item numbers in

Section D2

Hydraulic Section Parts

. Lettered parts are part of the air motor.

Tools Required

The following tools are needed to repair the hydraulic section:

Small and large adjustable wrenches

NOTE:

Do not use pipe wrenches, as they may mar the parts.

Wrenches with non-marring jaws, such as engineer’s or monkey

wrenches, are recommended. These wrenches can be purchased from

an industrial supply company.

in. socket wrench

Rubber mallet

English hex wrench set

Flat-bladed screwdrivers

Large, flat, clean work surface

Soft-jawed vise

Parker O-Lube or equivalent O-ring lubricant (Nordson part 1612251)

Loctite 242 Removable thread adhesive or equivalent (Nordson
part 900464)

Parts and kits to replace damaged components. Refer to

Section D2

Hydraulic Section Parts

Alignment tool (Nordson part 1102533)

Arbor press

Содержание PermaFlo 815




































































































Результаты поиска

Содержание PermaFlo 815

Отзывы:

Похожие инструкции для PermaFlo 815

Бренды по названию

Популярные бренды

Nordson PermaFlo 815, Руководство пользователя

Результаты поиска

Содержание PermaFlo 815

Отзывы:

Похожие инструкции для PermaFlo 815

Бренды по названию

Популярные бренды