Nordson PermaFlo 815 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 99

background image

Installation

B 3-2

Part 1102698

−

07

E

2019 Nordson Corporation

Mounting and Connections

(contd)

Task

Instructions

Mounting

Mount the pump vertically on a wall, stand, or wheeled dolly able to support the pump

weight and withstand vibration.
Use

1

/

2

-in. or 13-mm bolts and washers in the mounting slots so the air motor or

hydraulic section can be removed without removing the pump from its mounting.
If you use threaded studs in place of bolts in the two lower mounting slots you will not

be able to remove the hydraulic section without dismounting the entire pump.

Grounding

Connect the ground clamp to a true earth ground. The resistance to ground should not

exceed 20 ohms.

Air

Connections

Connect a 19-mm (

3

/

4

-in.) ID minimum air supply hose to the air inlet port. Do not use

rigid tubing, which transmits vibration.
Refer to

Section D1 Air Motor Parts

for the optional Air Motor Accessory kit, which

includes a hose and an air filter/regulator/gauge package.

Fluid

Connections

Refer to

Section A1 Quick Reference

for siphon and high pressure hose

recommendations, and

Section D2 Hydraulic Section Parts

for optional siphon hose

and circulation kits.
Connect the optional Siphon Accessory kit and/or Circulation kit to the siphon port.

The circulation kit includes installation instructions.

NOTE:

All siphon connections must be air-tight. Air leaks will affect pump priming and

cause cavitation.
Connect a high-pressure fluid hose to the high pressure fluid outlet port. Do not use

rigid tubing, which transmits vibration.

Remote

Exhaust

Option

Refer to

Section D1 Air Motor Parts

for the optional remote exhaust muffler kit. These

mufflers are equipped with 1

1

/

4

in. NPT fittings, for use in a header system to conduct

exhaust air away from the pump and reduce noise levels.
Remove the standard mufflers and replace them with the optional mufflers.
Connect flexible hose to the muffler fittings.
Slope the exhaust line downward away from the pump, to prevent moisture from

collecting in the line and draining back into the air motor.

«
...
25
26
27
28
29
...
»

Содержание PermaFlo 815




































































































Отзывы:

Нет отзывов

Похожие инструкции для PermaFlo 815

S15 Non-Metallic

Бренд: Sandpiper Страницы: 25

Бренд: AquaPRO Страницы: 4

Бренд: Gude Страницы: 64

Бренд: Stübbe Страницы: 32

Бренд: Energie Страницы: 31

HYDRA-SPRAY President A Series

Бренд: Graco Страницы: 20

OmniSpense ELITE

Бренд: Wheaton Страницы: 34

Бренд: Ribitech Страницы: 24

Бренд: Rotex Страницы: 80

Бренд: AMAZON COMMERCIAL Страницы: 48

Бренд: Kärcher Страницы: 50

Бренд: AmeriWater Страницы: 66

HydroTap G4 802701

Бренд: Zip Страницы: 24

Бренд: Zenit Страницы: 36

Бренд: XPOtool Страницы: 5

Бренд: felisa Страницы: 10

Akva Lux II TDv

Бренд: Danfoss Страницы: 28

Elmo Rietschle V-VTR 100

Бренд: Gardner Denver Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды