Nordson Encore LT страница 32 Скачать руководство пользователя

Страница: 32 / 92

System Setup

3-16

Part 1604857-04

2014 Nordson Corporation

Controller Configuration

Power Up Sequence

When power is applied to the system, the controller goes through the

following sequence:

1. All displays and LEDs light for 3 seconds.
2. The main control board configuration is displayed on the KV/



A panel:

: Auto (refer to troubleshooting to change the jumper if A is displayed)

: Manual

3. The controller software and hardware version are displayed on the

KV/



A panel in the form

N.NN

for 1 second.

NOTE:

If the spray gun is triggered on during power-up or wake up from

disable, the trigger LED blinks at a fast rate. Release the trigger and repeat

the sleep/wake up cycle.

Entering Configuration Mode

To enter configuration mode, press and hold the Plus and Minus buttons on

the kV/uA panel while either turning on power or pressing the

Enable/Disable button (if the controller is already powered up). After 1

second all panels flash

for 3 seconds. After 3 seconds the kV/



A panel

displays

−

for function 1. The controller is now in configuration mode.

To save your settings and exit Configuration Mode, press the

Enable/Disable button.

Atomizing Air
(Classic)
Total Flow
(Smart Flow)
Setting/Display

Select Charge

Mode Settings

KV/



A Setting/Display

KV/uA Selection

Control

Smart Flow Mode

Indicator

Flow-Rate Air

(Classic)

Powder Flow Rate

(Smart Flow)

Setting/Display

Enable/Disable

Trigger LED

Figure 3-16 Controller Interface

Содержание Encore LT





























































































Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды

Nordson Encore LT, Руководство по эксплуатации продукта

Результаты поиска

Содержание Encore LT

Отзывы:

Похожие инструкции для Encore LT

Бренды по названию

Популярные бренды