Nordson Encore LT Скачать руководство пользователя страница 31

Страница: 31 / 92

System Setup

3-15

Part 1604857-04

2014 Nordson Corporation

System Electrical Connections

Power Supply

CAUTION:

If you have a mobile system with a vibratory box feeder, check

the system identification plate for the correct voltage. Connecting a system

with a 115 Vac vibrator motor to 220 Vac could damage the vibrator motor.

The spray gun controller is rated for 100

−

240 Vac at 50/60 Hz, single phase,

and is marked as such, but the power supplied to the system must match

the vibrator motor rating.

Wire the system power cord to a customer-supplied three-prong plug.

Connect the plug to a receptacle that supplies the correct voltage.

Wire Color

Function

Blue

N (neutral)

Brown

L (hot)

Green/Yellow

GND (ground)

System Ground

Mobile Systems:

See Figure 3-15. Connect the ground cable attached to

the controller ground stud to a true earth ground.

Figure 3-15 System Ground Connection

Rail Mount Systems:

Locate the ESD grounding block kit. Follow the kit

instructions to install the grounding block to the grounded spray booth base.

Connect the flat braided ground cable from the controller ground stud to the

grounding block.

Содержание Encore LT





























































































Результаты поиска

Содержание Encore LT

Отзывы:

Бренды по названию

Популярные бренды

Nordson Encore LT, Руководство по эксплуатации продукта

Результаты поиска

Содержание Encore LT

Отзывы:

Бренды по названию

Популярные бренды