manualshive.com logo in svg

Nordson Encore LT, Руководство по эксплуатации продукта, Страница: 14 / 92

Поделиться
Скачать
Nordson Encore LT Скачать руководство пользователя страница 14

Description

2-2

Part 1604857-04

E

 2014 Nordson Corporation

Mobile System Components 

Mobile systems include:

S

Encore LT manual controller

S

Encore LT manual spray gun

S

Encore Generation II powder feed pump

S

Encore pump pickup tube

S

One of the following, based on system version:

S

Vibratory table and motor 

−

 fluidizes a 25- or 50-lb box of powder

S

50-lb Encore round feed hopper 

−

 fluidizes powder with low-pressure

compressed air

S

11-mm powder hose, air tubing, spiral wrap, Velcro straps

The components are mounted on a sturdy two-wheeled dolly.

Rail-Mount System Components 

Rail-mount systems include:

S

Encore LT manual controller

S

Encore LT manual spray gun

S

Encore Generation II powder feed pump

S

Pump adapter kit and coupling for use on HR/NHR feed hoppers

S

Rail-mount bracket kit

S

Grounding kit

S

11-mm powder hose, air tubing, spiral wrap, Velcro straps

S

Air filter kit

NOTE:  

Powder can be also be supplied from an Encore in-line pump

mounted in a feed center.

Wall-Mount System Components 

Wall-mount systems include a

S

Encore LT manual controller

S

Encore LT manual spray gun

S

Encore Generation II powder feed pump

S

Pump adapter kit and coupling for use on HR/NHR feed hoppers

S

Wall-mount bracket kit

S

Grounding kit

S

11-mm powder hose, air tubing, spiral wrap, Velcro straps

S

Air filter kit

NOTE:  

Powder can be also be supplied from an Encore in-line pump

mounted in a feed center.

Содержание Encore LT





























































































Отзывы:

Нет отзывов