Nordson Encore HD iControl 2 Скачать руководство пользователя страница 81

Страница: 81 / 114

4-31

Touch Screen Troubleshooting

Touch Screen Calibration

The touch screen is calibrated at the factory. If changing a program card or the iControl 2

PC, or if having problems touching screen components accurately, recalibrate the screen.
The touch screen calibration values are stored on the program card. If you install a

program card that has not been used before, there will be no calibration file on the card.

The system will automatically start the calibration procedure.

NOTE:

If installing a program card that was previously used on another iControl 2

console, performing the

Calibration with a Mouse

procedure on the following page MUST

be done to calibrate the touch screen.

Normal Calibration

Calibrating the touch screen can be done at any time. To start a normal calibration, start

the Program Shutdown procedure. When the operating system shutdown prompt appears

on the screen, touch the Cancel button, then touch the CAL button.

Follow the calibration instructions on the screen exactly, using your finger to touch the

targets. When you have completed the calibration procedure, touch the iControl 2 button

to start the iControl 2 software.

Problems During Calibration

Failure to follow the calibration instructions exactly:

Unable to touch the center

Completion

button and exit the calibration procedure. If this happens, stop and wait

until the procedure times out. Then, repeat the procedure and complete it correctly. After

completing the calibration procedure, touch the

iControl 2

button to start the iControl 2

software.

If console power is shut off during the calibration procedure:

The calibration file on

the program card will be corrupted. On power up, you will not be able to touch the CAL

button to start the calibration procedure. If this happens, perform the

Calibration with a

Mouse

procedure.

Содержание Encore HD iControl 2



















































































































Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды

Nordson Encore HD iControl 2, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore HD iControl 2

Отзывы:

Похожие инструкции для Encore HD iControl 2

Бренды по названию

Популярные бренды