Nordson Encore HD iControl 2 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 114

background image

© 2022 Nordson Corporation

4-29

Troubleshooting

Other Fault Messages and Conditions

Table 4-10 Other Fault Messages and Conditions

Message or Condition

Cause/Correction

Message: Too many (few) control

nodes found

The number of spray gun cards/iFlow modules does not match the number of

spray guns setting in Guns Configuration screen (System Configuration). This

could be a normal condition if you have an odd number of spray guns in your

system. The red Fault LED on the spray gun card will light if two spray guns are

not connected to the card.

Message: Failure reading database

No data or configuration displays on screens. User data card missing, defective,

or wrong size. Replace the card.
Compact Flash adapter failure. Replace the adapter.

Condition: iControl 2 screen

partially boots up. Screen is blank

except for possible text display, or

screen displays “Hit ESC for

.altboot...”

Program card is missing, blank, or defective. Replace the card.
Program card in wrong adapter slot. Insert the program card in the outer slot.
Compact Flash adapter failure. Replace the adapter.
No power to Compact Flash adapter. Check the power cable and connection to

the adapter.
Check the ribbon cable connections to the Compact Flash adapter and PC.

Replace the ribbon cable if necessary. (Standard 40-pin IDE cable, not available

from Nordson.)

Condition: Pickoff value is reset to

smaller number after entry

The maximum pickoff length is 4096 inches (104038.4 mm). With the keypad you

can enter a number larger than the maximum, but when you save your entry the

value will be automatically reduced to the maximum value.

Condition: Inconsistent lead and

lag timing for auto gun triggering or

moving

Conveyor encoder pulse rate is too fast. Maximum is 10 Hz (10 pulses/second).

Some pulses are not being detected. Reduce the conveyor speed or change the

encoder-to-conveyor linkage to reduce the pulse frequency.

Condition: Lockout message does

not display when keyswitch turned

to lockout position, or lockout

cannot be canceled by turning

keyswitch to another position

Booth exhaust fan is off (turning off switched power to the console), or remote

lockout is on.

If the exhaust fan is turned off before turning the switch to Lockout, then lockout

cannot be activated. If the fan is turned off after the switch is turned to Lockout,

then lockout cannot be canceled. Turn fan on to correct.

If the remote lockout is on, turn it off. Remote lockout is activated by a customer-

supplied switching device connected to the remote lockout relay in the console.

Condition: iControl 2 screen is

locked up (no response)

Cycle console power. If the condition persists, the program card is corrupted.

Obtain and install another program card. Refer to Touch Screen Calibration when

installing new program cards.

Condition: Air flow when gun is not

triggered on

iFlow module requires re-zeroing. Re-zero the iFlow module as described on

page 4-12.
iFlow module proportional valve or solenoid valve stuck open. Refer to the Repair

section for instructions on cleaning the proportional valves. Solenoid valves must

be replaced if they do not close.

«
...
77
78
79
80
81
...
»

Содержание Encore HD iControl 2



















































































































Отзывы:

Нет отзывов

Похожие инструкции для Encore HD iControl 2

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: CAME Страницы: 32

Бренд: 3M Страницы: 34

Бренд: GBD Страницы: 68

Бренд: Barco Страницы: 2

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: Eaton Страницы: 96

Бренд: CAME Страницы: 2

Бренд: Dahua Страницы: 137

Omnicharge Solar OCS 100-20

Бренд: tbs electronics Страницы: 64

Бренд: Mitsubishi Страницы: 30

BIS U-830-4-011-H-1

Бренд: Balluff Страницы: 2

Бренд: Aqua Lung Страницы: 24

Бренд: McIntosh Страницы: 68

SmartStuff Series

Бренд: TCP Страницы: 2

NuDAQ cPCI-7248

Бренд: ADLINK Technology Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды