Nordson Asymtek Spectrum S-920 Скачать руководство пользователя

Страница: 188 / 238

8-14

Troubleshooting

8.4.12 Substrate Heaters

Table 8-12 Substrate Heater Troubleshooting

Symptom

Possible Cause

Recovery

Missing vacuum hole screw(s)

Replace screw(s).

Hissing air leak

Other pneumatic leaks

Contact a service technician.

Erroneous temperature

display

Wrong display unit

Change display unit to C.

Workpiece part not held

steady

Check for improper open or
plugged vacuum holes

Remove and install screws as applicable.

Vacuum does not start or
fails to work properly

System has low or no air pressure

1. Verify air is connected to facility air supply.

2. Set main air regulator to approximately

90 psi.

Set Point (SP) value below Present
Value (PV)

Change the SP value within the Heater Controls
Window. See

6.9.2 Setting the Heaters

Disconnected heater

Verify the heater cable connections are securely
attached to the correct ports.

Hardware or software failure

Contact a service technician.

Hot plate does not heat

Blown fuse on the Conveyor/Heater
Controller

Check the fuses by the heater power
connections on the conveyor controller and
replace if necessary. See

9.10 Replacing Fuses

8.4.13 Conveyor

Table 8-13 Conveyor Troubleshooting

Symptom

Possible Cause

Recovery

EMO button has been activated

1. Turn the EMO button clockwise until it pops

back into position.

2. Press

(

) on the operator’s console.

X or Y Motor cables are loose

Call a trained service technician.

Fuse is blown in Conveyor/Heater
Controller Power Supply

Check the fuses by the heater power
connections on the conveyor controller and
replace if necessary. See

9.10 Replacing Fuses

Rails or belt will not move

Conveyor/Heater Controller
malfunction

Call a trained service technician.

Tooling Air pressure is too low

Adjust Tooling Air Pressure Regulator to supply
275 kPa (40 psi).

There is an air leak in a pneumatic
line or component

Leaking component or line must be located and
repaired or replaced. Call a trained service
technician.

The pneumatic device has failed

Call a trained service technician.

Solenoid Valve is defective

The Solenoid Valve must be replaced. Call a
trained service technician.

Stop pins, lift tables or
clamps are inoperative

Conveyor may not be properly
configured in Fluidmove

Call a trained service technician.

Содержание Asymtek Spectrum S-920















































































































































































































































Результаты поиска

Содержание Asymtek Spectrum S-920

Отзывы:

Похожие инструкции для Asymtek Spectrum S-920

Бренды по названию

Популярные бренды

Nordson Asymtek Spectrum S-920, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Asymtek Spectrum S-920

Отзывы:

Похожие инструкции для Asymtek Spectrum S-920

Бренды по названию

Популярные бренды