Nordson Asymtek Spectrum S-920 Скачать руководство пользователя | Manualshive

Страница: 186 / 238

background image

8-12

Troubleshooting

8.4.10 Needle Heater

Table 8-10 Needle Heater Troubleshooting

Symptom

Possible Cause

Recovery

Set Point (SP) value below Present
Value (PV) or the heater is in an
idle state

Change the SP value within the Heater Controls
Window. See

6.9.2 Setting the Heaters

Disconnected heater

Verify the needle heater cable connections are
securely attached to the correct ports.

Failed DHC power

Verify DHC indicator lights for 3.3V, -12V, and
12V are illuminated.

No needle heat

Failed heater

Verify the needle heater electrical parameters.
The resistance between pins 4 and 5 for the
heating element should be 100 ohms +/- 5 ohms.
The resistance of the RTD sensor between pins
6 and 7 should be 108 ohms, +/- 5 ohms.

8.4.11 Tactile Sensor

Table 8-11 Tactile Sensor Troubleshooting

Symptom

Possible Cause

Recovery

During setup routine,
error indicates that the
tactile sensor is already
engaged

Tactile sensor cap is stuck in the
down position

Visually inspect the sensor cap for fluid buildup.
If there is fluid, clean as specified in

Tactile Sensor Error.

If there is no fluid, call a

service technician.

The tactile sensor signal can be tested from the
Fluidmove

Tools > IO

menu. Select IO and

inputs. Locate the tactile cap signal display and
monitor its state as the cap is depressed and
released. If the state does not change, the
precision switch may have failed.

Needle-to-height-sensor
offset is inaccurate

Fluid build-up on probe tip or tactile
sensor cap may have caused
inaccurate height sensor calibration

1. Clean probe tip/tactile sensor cap. See

8.4.11.1 Tactile Sensor Error

2. Perform a “Valve Offsets” routine in FmXP.

For assistance, refer to the

Fluidmove User

Guide

or Online Help.

«
...
184
185
186
187
188
...
»

Содержание Asymtek Spectrum S-920















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Asymtek Spectrum S-920

Бренд: WaterCare Страницы: 28

Бренд: Canaturena Страницы: 11

Бренд: Electrolux Страницы: 9

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 16

Бренд: Electrolux Страницы: 32

Бренд: HENDRX Страницы: 40

Бренд: Shopnsave Страницы: 7

Бренд: Bobrick Страницы: 2

Бренд: AQUABEVE Страницы: 6

Бренд: HURAKAN Страницы: 41

Majestic SK5MAJ

Бренд: Silver King Страницы: 12

Бренд: Lancaster Страницы: 14

Бренд: Zip Страницы: 28

Бренд: Modena Страницы: 23

Бренд: Kogan Страницы: 12

Rubbermaid H-3542

Бренд: U-Line Страницы: 6

Бренд: U-Line Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды