Nordson Asymtek Spectrum S-920 Скачать руководство пользователя страница 128

Страница: 128 / 238

6-4

Operation

6.5

Adjusting the Air Pressure

6.5.1 Adjusting the Main Air Pressure

Verify that the facility air is connected to the Main Air Pressure Regulator Inlet.

TIP

For accurate pressure adjustment, lower the pressure below the desired level and

then increase to the desired pressure.

Rotate the knob on the Main Air Pressure Regulator counterclockwise until the Main Air
Gauge registers 0 psi.

Rotate the knob clockwise until the Main Air Pressure Gauge registers 90 to 100 psi (621 to
689 kPa).

If the Main Air Gauge fails to register pressure, verify that the dispensing system is
connected to the facility air source.

Monitor the Main Air Gauge to make sure that pressure builds at a steady rate. Watch for
dropping pressure indicating an air leak.

If there is an air leak, identify the source, shut off the facility air, and fix the leak before
proceeding.

Item Description

Main Air Pressure Regulators

Main Air Pressure Gauges

Figure 6-3 Main Air Pressure Regulator and Gauge Sets

Содержание Asymtek Spectrum S-920















































































































































































































































Результаты поиска

Содержание Asymtek Spectrum S-920

Отзывы:

Nordson Asymtek Spectrum S-920, Инструкция по установке, эксплуатации и обслуживанию, Страница: 128 / 238

Результаты поиска

Содержание Asymtek Spectrum S-920

Отзывы: